Technical Support | Headsight, Inc.

Truesight 2 (2.15.42)
IMPORTANT: All settings and calibrations will be reset to default if updating to this version from 2.14.4(TS2-2.14.40) or earlier
- Add: Support for updating Truesight Remote from the Truesight 2 Base (on supported Remotes)
- Add: Info screen if Truesight Remote is connected to an unsupported Truesight Base
- Add: VT support for hours that the system has been ENGAGED (About Screen)
- Add: VT support for GPS signal indicator (Signal lost, acquiring, acquired)
- Add: Going over Max Speed (default 10mph) will put Truesight in Road Mode
- Add: System will default to CAN speed selection if no GPS signal is detected during initial calibration
- Add: Wheel angle voltage will now be shown during initial calibration
- Fix: SSID for Wifi mode now broadcasts as intended
- Fix: Voltage for feedback input is now correct if sensor is lost (was displaying .3V if a sensor was lost, instead of correct 0V)
- Fix: General text changes
- Remove: Linked serial number on About screen
- Upd: Settings are no longer stored in the Truesight Remote (if connected via Truesight 2 Base). Settings are instead stored in the Truesight 2 Base.
- Upd: Changing systems while engaged will now disengage Truesight.
- Upd: Steering systems are now sorted alphabetically
- Upd: Auto-Engage, after leaving Road Mode, now requires a manual raise-lower of the feederhouse to prevent unintentional auto-engages
- Upd: ISObus ECU info for Headsight controllers now shows more correct/useful information
Truesight Remote (With Truesight 2 base only) (2.42)
- Add: A screen will now show if a Truesight Remote is connected to an incompatible Truesight or Truesight 2 base
- Upd: Settings are no longer stored in the Truesight remote. Settings will now be synchronized with the settings in Truesight 2 base
*HZ Bootloader v1.3.8, TS2 Bootloader v1.3.8, ONYX 3.39a, CSG 0.0.1

View Updates

Download File View Previous Updates

Horizon Software - 2.15.1

Instructions for how to upgrade to the new Horizon software are included in the downloaded zip file in PDF form.

Horizon (2.15.1)
IMPORTANT: You will lose any settings and calibrations when you update to this version from 2.14.4 (TS2-2.14.40; TS-2.40) or earlier
- Add: Split-Flex® header app now supports Independent Wing Control header configuration
- Add: MAYA® corn header app
- Add: Sensor errors will now persist until “Clear Errors” button is pressed on Errors page
- Add: Support for Case-IH x250 and x150 combine models
- Add: Support for Feederhouse Angle (HFAT) via CAN on newer CIH models
- Fix: Terrahawk: RMS no longer displays as x10
- Fix: Terrahawk: Fixed an issue where sensor calibration data was lost if sensor positions were changed after calibration
- Fix: Terrahawk: Start distance now is assigned to correct sensor
- Fix: Feathersight bar graph on Diag screen will now update while Terrahawk Sensor Type is selected
- Fix: Capello: Certain folding header configurations were not allowing “Fold” button to show up
- Fix: General text changes
- Remove: Linked serial number on About screen
- Upd: ISObus ECU info for Headsight controllers now shows more correct/useful information
Truesight 2 (2.15.42)
- Add: VT support for hours that the system has been ENGAGED (About Screen)
- Add: VT support for GPS signal indicator (Signal lost, acquiring, acquired)
- Add: Going over Max Speed (default 10mph) will put Truesight in Road Mode
- Add: System will default to CAN speed selection if no GPS signal is detected during initial calibration
- Add: Wheel angle voltage will now be shown during initial calibration
- Fix: SSID for Wifi mode now broadcasts as intended
- Fix: Voltage for feedback input is now correct if sensor is lost (was displaying .3V if a sensor was lost, instead of correct 0V)
- Fix: General text changes
- Remove: Linked serial number on About screen
- Upd: Changing systems while engaged will now disengage Truesight.
- Upd: Steering systems are now sorted alphabetically
- Upd: Auto-Engage, after leaving Road Mode, now requires a manual raise-lower of the feederhouse to prevent unintentional auto-engages
- Upd: ISObus ECU info for Headsight controllers now shows more correct/useful information
*HZ Bootloader v1.3.8, TS2 Bootloader v1.3.8, ONYX 3.39a, CSG 0.0.1

View Updates

Download File View Previous Updates

Insight Software - 4.01

Instructions for how to upgrade to the new Insight software are included in the downloaded zip file in PDF form.

Feathersight lost pressure sensor updates, set outputs to minimum, status light = red w/green blink
Foresight unlock code value update
Added Spanish language support. Note this makes the file too big for R4 and earlier, an English only version is available if required.
Update Insight screen "logo"
Selection arrow defaults to Setup not Perform Cal
Added combine select text for CIH 9250
Removed clipping of unscaled feathersight input
Updated CMT limits
Update CNH model text, changed from "5088 - 9240 AFX" to "5088 - 9250 AFX"
Added a set fuses command so configuration settings are not overwritten by a software update
Add Tilt Balance to setup menu for JD10
Added software version number to logo page
Fixed a problem with R8 version boxes that caused Foresight and box hours to be lost after reset

View Updates

Download File View Previous Updates

Truesight Software - 2.40

Instructions for how to upgrade to the new Truesight software are included in the downloaded zip file in PDF form.

Truesight (2.40)
IMPORTANT: This software is intended for original Truesight system only (Not Truesight 2)
- Version number updated

View Updates

Download File View Previous Updates